Skripsi
ANALISIS TEMPERING DENGAN QUENCHING MEDIA OLI MESRAN SAE 40 TERHADAP SIFAT MEKANIK POROS S 45 C
Indonesia :
Heriy Kuswanto, 2010," Analisis tempering dengan quenching media oli mesran SAE 40 terhadap sifat mekanik poros baja S45C." Teknik Mesin Fakultas Teknik Universitas Pancasakti Tegal.
Penelitian ini bertujuan untuk mengetahui pengaruh temper dengan quenching media pendingin oli mesran SAE 40 terhadap sifat mekanik pada baja S45C. Proses temper dilakukan pada suhu 3000 dengan waktu penahanan ( holding time ) 60 menit dengan quench pada suhu 8700 dengan waktu penahanan 30 menit.
Metode yang digunakan dalam penelitian ini adalah deskriptif, bahan baku material untuk spesimen adalah baja S45C importir PT. TIRA AUSTENITE. Spesimen uji tarik menggunakan standar JIS Z2204 dan Uji kekerasan menggunakan standar JIS Z2245.
Pengujian komposisi kimia menunjukkan baja S45C masuk kedalam golongan baja karbon sedang dengan kandungan karbon 0,44 %. Hasil uji kekuatan tarik baja S45C setelah mengalami perlakuan panas quenching-temper dengan kedua media temper yang berbeda yaitu media udara bebas dengan hasil kuat tarik ( tensile strength ) lebih tinggi sebesar 1096,86 N/mm2 dari pada dengan media oli sebesar 783,38 N/mm2 akan tetapi untuk perpanjangan ( elongation ) rata-rata media udara bebas 3,62 % dengan besar rata-rata kontraksi 32,36 % , bila dibandingkan dengan oli dengan rata-rata sebesar 7,18% dengan rata-rata kontraksi 48,96%. Hasil uji kekerasan dengan temper media udara bebas dengan rata-rata 185,33 HB lebih besar dibandingkan dengan hasil uji temper media oli rata-rata sebesar 173 HB.
Dari hasil pengujian logam tersebut bahwa perlakuan quenching temper dengan media oli disarankan bila ingin menghasilkan logam dengan tingkat keuletan yang cukup tinggi sehingga logam lebih dapat dibentuk.
Kata kunci : quenching,tempering, kekuatan tarik, poros S45C
English :
Heriy Kuswanto, 2010, "Analisis of tempering-quenching media of oli mesran SAE40 towards the characteristic machine of steel S45C." Engineering The Faculty of Technique Pancasakti University Tegal.
This research intends to know the influence of temper and quenching cooling media of oli mesran SAE40 towards the characteristic of machine of stell S45C. The proses of temper is conducted in 300C with the holding time 60 minute while the process of quenching is conducted in 870C with the holding time 30 minute.
The method used in this research is descriptive. The raw material for the specimen is stell S45C, imported by PT.TIRA AUSTENITE. The specimen of pull test use standard JIS Z 2204 and hardness use standard JIS Z2245.
The chemical composition testing shows that steel S45C enter in the medium carbon steel with the content carbon 0,44%. The result of tensile strength of steel S45C after heating by temper-quenching by using the two different medias of temper, those are free air which result of the tensile strength is 1096,86 N/mm2, it is higher than oil which result is 783,38 N/mm2. However, the average elongation of free air is 3,62% with the average contraction 32,36%. It is smaller than the average elongation of oil that is 7,18% with the average contaction 48,96%. The average result of strength testing temper media of free air is 185,33 HB. It is bigger than the average result of temper test by using oil that is 173 HB.
From the result of the steel testing, the temper-quenching by using oil as the media is suggested to be used if we want to produce the steel with a high level of the though, so that the steel is easier to be formed.
Key words: quenching, tempering, tensile strength of shaf S45C
932011KI1 | Tersedia |
Tidak tersedia versi lain